Expert Answers about Ford F-100, F-150, F-250, F-350

• Black Westin Fey Diamondstep Replacement Rear Bumper for 1978 Ford F-100
• Although the # 20009 Westin Diamondstep bumper isn't the correct fit for your truck, we do offer one that is. For that style bumper in black powder coat, use part # 20000-92230 which includes both the bumper and the custom fit brackets for your 1978 Ford F-100. This is a confirmed fit per Westin.
  view full answer...


• Recommended Truck Bed Mat For A 1966 Ford F-100
• While we don't carry any custom-fit options for a 1966 Ford F-100 we do offer universal-fit options like the DeeZee Universal Utility Mat for Trucks and Trailers # DZ85005. DeeZee also offers a universal-fit tailgate liner # DZ86700 in a similar style to help protect your truck bed. Both of these universal-fit mats can be trimmed to fit your bed and tailgate.
  view full answer...


• Can The Air Lift SlamAir Air Helper Springs # AL59106BT Accommodate A 3" Wide Leaf Spring
• The bottom bracket of the Air Lift SlamAir Air Helper Springs for Lowered Trucks # AL59106BT has approximately 3-1/8" of space so you would be able to install it over a 3" wide spring.
  view full answer...


• Wiring Vehicle and Trailer Connectors
• Wiring 7-way connector # PK12706 on your trailer and 7-way socket # PK12-707E on a vehicle like your 1975 Ford F-250 is simple; all you will need is an auxiliary 12 volt battery and a circuit tester such as # PTW2993. You will need to wire the connectors via function, which are displayed in the accompanying photo. To determine the functions of the wires run on your truck, have a helper engage them while you use the circuit tester and attach them to the 7-way Trailer Socket # PK12-707E. The...
  view full answer...


• Dimensions of Draw-Tite Max-Frame Trailer Hitch Receiver Part # 75034
• I do have some dimensions of the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75034 which is a fit for a 1965 Ford F-100 and I have attached these for you below but I would not be able to provide a dimensional drawing as this is proprietary information that is not released by the manufacturer. The distance from the frame to the top of the receiver tube opening is 5-5/8" which will allow you to determine how far under the rear bumper the receiver tube will sit. In regards to exhaust...
  view full answer...


• Towing Mirror Fit for 1966 Ford F100
• The CIPA # 11902 you'd looked at would fit the mirror shown in the provided photo, which is found on 1999-2008 Ford Super Duty trucks as well as the 2000-2005 Ford Excursion. It wouldn't be a fit for the 1966 F-100, but we do offer mirrors that would work. Because your existing mirrors are round, universal clip on mirrors wouldn't be a fit, but the CIPA # 11650-2 which actually attaches to the door via ratcheting straps would work. They aren't the best looking option in the world, but...
  view full answer...


• Adapter for 4-Flat on Truck and 7-Way on Trailer
• We do have a solution for you, though the Reese Trailer Connector Adapter # 78118 will not work for you. Instead I recommend the Hopkins Endurance Quick-Install Trailer Connector Adapter # HM47200 which will plug into your truck's 4-way and allow you to connect your trailer's 7-way.
  view full answer...


• Will Curt Class IV Trailer Hitch Receiver Fit 1974 Ford F-250 with Standard Bumper and 34 Inch Frame
• The Curt # C14082 will fit on your 1974 Ford F-250 as long as you have the crew cab. It does bolt on but will require drilling into the frame to install. I've attached a link that shows all of the Class IV hitch receivers confirmed to fit the different models of your F-250. If you also need a wiring harness use the Hopkins # 40105 for a 4-way connector or the Draw-Tite # 20023 for a 7-way. You might like an adjustable ball mount. The B&W Tow & Stow # BWTS10048B provides up to either...
  view full answer...


• Recommended Trailer Hitch Receiver For A 1982 Ford F-350 DRW With Deep Bumper
• Since your 1982 Ford F-350 DRW has the Deep Bumper I recommend the Curt 3-Piece Trailer Hitch Receiver - Multi Fit - Class V - 2" # C15511 as it will work with both 34" and 37-1/2" wide frames so you will not have an issue. The # C15317 you were looking at is only confirmed to fit the 1988-2000 Chevrolet C/K series pickups with the 10" drop bumper and would not fit your F-350. Keep in mind that while the # C15511 has a 1500lb tongue weight rating and 15000lbs trailer weight rating your...
  view full answer...


• Recommended Universal Truck Bed Mat for a 8 Foot Bed
• We have a universal mat that should fit the bed of your 1964 F-100 since you have the 8' bed. It is the DeeZee Universal Utility Mat for Trucks and Trailers Item # DZ85005. This bed mat is 8' long x 4' wide. This 3/8" thick rubber mat has a non-skid surface that prevents cargo from shifting. I have linked a review video below so you can take a look at this mat being installed and used. There are no custom fit options for a 1964 F-100.
  view full answer...


• Class V Trailer Hitch for 1972 Ford F250 with Barden Bumper
• I am unfamiliar with the Barden Bumper and in my research, I could not find any specific information regarding the Barden Bumper. Our trailer hitches are not tested with aftermarket bumpers. We have two bumpers that have been determined to be a fit for your truck with a factory bumper. The # BWHDRH25122 is for standard and step bumpers and the # BWHDRH25198 is for deep drop bumpers. I recommend measuring from your frame to the bottom of your bumper to know how much distance you will need...
  view full answer...


• Will Access TonnoSport Fit a 1979 Ford F-100 Fleet Side Pickup
• The Access TonnoSport Soft, Roll-Up Tonneau Cover # A22010029 will fit the 6' Fleet side bed on your 1979 Ford F-100. I don't have the exact dimensions of this cover (all of the tonneau manufacturers just reply to that question with "it fits") but the "Standard Bed" we have listed in our fitguide is the Fleet side so you're good to go!
  view full answer...


• Custom Snow Plow Mount for 1976 Ford F-250
• You're in luck because there are custom mounting brackets for a snow plow that fit your 1976 Ford F-250 (so long as it is not a SuperCab model), the Custom Mounting Brackets for Detail K2 Snowplows # K281501. These mounting brackets work with the following snow plows: - Detail K2 Summit II Snowplow # K2SUMM8826 - Detail K2 Summit II Elite Snowplow - Electric Actuator # K2SUMM8826ELT
  view full answer...


• Trailer Hitch Recommendation for a 1976 Ford F-Series Truck with 4 Wheel Drive
• A high boy is a generic term used to encompass all Ford F-250 4x4 trucks from the late 1960s to the late 1970s (circa 1967 to 1977 and a half). If your 1976 is an F-250 with 4 wheel drive, it falls under the high boy umbrella. F-100 and F-150 models are not considered high boys even though 4 wheel drive was an option for some. The high boy trucks came with a different transfer case (what is called a divorced transfer case), the front cross member set up was different, and they sat higher...
  view full answer...


• Trailer Hitch Receiver Fit For 1965 Ford F-250 With Custom Bumper
• Outstanding photos thank you so much for sending them, and based on that we do have a hitch that can fit your 1965 Ford F-250 with a custom bumper. Since the frame is clear from any interference with the bumper, all you need to do is measure from the frame to the bottom of the bumper and see what that distance is. If that distance is 7-1/4 inches or less there is a hitch you can use: - Curt Trailer Hitch Receiver # C13099 The reason why is the Curt # C13099 measures 7-1/4 inches from...
  view full answer...


• Will the Westin Fey Diamondstep Bumper # 73000 Fit My 1977 Ford F-250?
• I have a solution for you. Unfortunately, the Westin Fey Diamondstep # 73000 will not fit your 1977 Ford F-250. However, for the correct bumper and mounting hardware, you need the Westin Fey Diamondstep Rear Bumper with Custom Installation Kit # 21000-92230. This bumper comes with the same chrome style as the # 73000. Also, it comes with all mounting hardware include for a quick bolt-on installation. It is important to note that this bumper will only fit standard beds. If you do not have...
  view full answer...


• Recommended Trailer Hitch Receiver for 1979 Ford F-250
• I recommend the Curt Class III Trailer Hitch Receiver # 13028 for your 1979 Ford F-250. This hitch will fit either the standard bumper or the deep drop bumper. It will however, not fit if you have lower rear fascia or a rollpan or tube bumper. It is a bolt on installation but does require some drilling. For trailer wiring you can use the Tekonsha Wiring Harness # 18252. This will add a 4-pole onto the back of your truck and includes quick-splice connectors to make it easier to hardwire. If...
  view full answer...


• Replacement Rear Bumper Options For A 1976 Ford F-250
• Yes, we have the following style options available for your 1976 Ford F-250 with brackets compatible with your 34" frame: Westin Fey Surestep Deluxe XLT Rear Bumper with Custom Installation Kit - Chrome Plated Steel # 21007-92230 Westin Fey Diamondstep Rear Bumper with Custom Installation Kit - Chrome Plated Steel # 21000-92230 Westin Fey Surestep Rear Bumper with Custom Installation Kit - Chrome Plated Steel # 21002-92230 Westin Fey Diamondstep Rear Bumper with Custom Installation...
  view full answer...


• Replacement Regulator For Marshall Brass Co 240 Regulator
• The Camco Automatic Changeover part # CAM59005 will replace your marshall brass co model 240 without a problem. We do not carry the marshall brass co models but from what I could tell from my research they are just standard manual dual regulators. I was not able to find a BTU rating on the 240. The Camco Automatic Changeover part # CAM59005 will automatically switch tanks for you when one is empty.
  view full answer...


• Class V Trailer Hitch for 1973 Ford F-350 with 34 Inch Frame
• I checked with B&W and the Class V B&W Heavy-Duty Trailer Hitch # BWHDRH25122 is a confirmed fit for the 34 inch frame on your 1973 Ford F-350 that has a 10 inch step bumper. The only thing you may need to do is remove or modify the spare tire carrier (if your truck has one) in order to ensure there is not interference with the hitch. I have added a link to the installation instructions of this hitch for you to check out as well.
  view full answer...